Tidal Datums vs Vertical Geodetic Datums
TIDAL DATUMS reflect the interface between water and land and are defined by the tidal variation. For example, a tide gauge in the water measures mean sea level. Tidal datums are localized because the transition between types of datums can shift quickly. It's also time-dependent.
GEODETIC DATUMS are reference surfaces of zero elevation to which heights are referred to over a large geographic extent. These datums are used to measure the height (altitude) and depth (depression) above and below mean sea level. Commonly used vertical datums in North America are the National Geodetic Vertical Datum of 1929 (NGVD29) and the North American Vertical Datum of 1988 (NAVD88).
A (vertical) geodetic datum often ties in tidal datums. A geodetic datum reference might use a tidal datum as a starting point. If you think about it, a community's height system should be consistent with a tidal datum because that's where the water will flow.
Types of Reference Heights
There are different types of heights to be aware of when referring to a vertical datum. These are the 3 primary types of heights, although other types of heights exist:ORTHOMETRIC represents the height distance between the Earth's surface and geoid at a specific point. Surveyors usually refer to orthometric heights. When you take the height at the peak of a mountain. It's an orthometric height measured as the distance between the surface and the geoid.
GEOID coincides with mean sea level as if you are imagining it as an extension under (or over) land areas. The geoid is an equipotential surface at which gravity is normal – closely approximating mean sea level. This is because of the varying densities that are present on the Earth at different places. There are gravity anomalies with undulations differing from place to place.
Land and mountains prevent us from seeing the geoid surface of the Earth. The Earth's interior differs in density everywhere. This means that gravity varies everywhere on the Earth. This is why we measure gravity or the gravitational equipotential surface. We can then infer that this is how water would settle and model it mathematically. The geoid then gives a true zero surface for measuring elevations.
REFERENCE ELLIPSOID is the reference ellipsoid is a mathematical model of the shape of the Earth with the major axis along the equatorial radius. It approximates the geoid but mostly coincides with geodetic network computations to which point coordinates (latitude and longitude) are referred.
1. National Geodetic Vertical Datum of 1929 (NGVD29)
Commonly used vertical datums in North America are the National Geodetic Vertical Datum of 1929 (NGVD29) and the North American Vertical Datum of 1988 (NAVD88).These 26 tide gauges were set up in harbors along the east and west coast of the United States (and along the Gulf of Mexico. Twenty-one stations were in the United States and five in Canada.
During a twenty-year period beginning in 1877, a “level line” was surveyed across the entire United States. As the network of level lines across the country expanded, this became the basis for the vertical datum.
NGVD29 was the system used by surveyors, engineers, and mapping for most of the 20th century. But it was replaced by the more accurate North American Vertical Datum of 1988 because of its importance in floodplain management.
2. North American Vertical Datum of 1988
One of the main reasons for the change to NAVD88 was because the National Geodetic Survey (NGS) found that the sea was actually not level at all. There were local variations caused by wind, currents, and topography of the sea bed.The numbers didn't fit because the mean sea level was higher at one location compared to elsewhere. Eventually, satellite technology found that these distortions were caused by gravity.
The 1988 vertical datum was based on over 600,000 kilometers of control leveling. It also used satellite technology to improve on earlier vertical datums.
The tools for accurate elevation measurement have also remained fairly consistent over the years with the use of level rods and a sighting instrument to measure the height differences between two points. Today a laser may replace the use of a telescope but the approach remains the same.
Eventually, satellites such as GRACE and GOCE paired with GPS technology found that these distortions were being caused by gravity. These satellite systems account for differences in gravitational forces in different areas.
Floodplain Mapping with the Vertical Datum
If we say that floodwaters will rise 25 feet, what exactly is “25 feet” referenced to? We need a consistent starting point to compare flood and ground elevations. This is why consistent vertical datums and mean sea level are so important. Effective floodplain management depends on accurate surveying.
During new construction, FEMA measures proposed structure elevations. They compare base flood elevations to ensure that new construction will be reasonably safe from flooding.
What's important is that all survey points must use the same vertical datum throughout the survey. Differences in vertical datums can range from three feet or more in the Rocky Mountains where gravitational forces are high… to a couple of inches in other areas.
NAVD88 corrects many of the problems with NGVD29. The 1988 vertical datum was based on over 600,000 kilometers of control leveling performed since 1929 and reflects geological crustal movements or subsidence that may have changed benchmark elevation.
If you were to perform surveys for floodplain mapping, up until recently most flood insurance maps used NGVD29. However, FEMA has made the switch to NAVD88.
Vertical Datum Transformation
A vertical coordinate transformation isn't a simple plug-in-play formula. These transformations require software to transform into different vertical datums. The NAVD88 is a correction of thousands of control points of elevation datum.
VDatum is a free tool by NOAA to transform data among a variety of tidal, orthometric, and ellipsoidal vertical datums. Users can convert their data from different horizontal/vertical references into a common and desired reference level.
Conclusion
A horizontal coordinate system gives us latitude and longitude. A vertical datum is another component of your typical horizontal coordinate system.Most vertical datums in North America use sea level as the basic reference plane from which we measure elevation changes. With mean sea level (MSL) as a reference point of zero, it is possible to measure height or topography accurately. We can also begin to understand if ocean levels are rising or falling over time.
We are on a three-dimensional planet that has ups and downs in addition to the side-to-side in a horizontal coordinate system on the surface.
To handle the ups-and-downs, we have the vertical datum which gives a place to set the zero measurements with mean sea level as the basis for our ups-and-downs. This is called the geoid.
References
Geoid from NASA's Grace Mission – Image Courtesy of NASA/JPLTable of contents
- Latitude, Longitude and Coordinate System Grids
- Where is the Central Meridian?
- Greenwich Meridian (Prime Meridian)
- Lost in Null Island: The Curious Origin of 0,0
- Degrees/Minutes/Seconds (DMS) vs Decimal Degrees (DD)
- What is a Horizontal Datum Reference Frame?
- Vertical Datum – Earth's Elevation Reference Frame